What device may have a rotating table surface and/or spikes on the table surface for a better grip? a. Roller skid b. Pallet jack c. Pallet conveyor d. Accumulating conveyor
Roller skid
Oops!
Check
Okay!
Check
monster
Reset all scores!
Oops!
rocket
Go to first place!
Okay!
gift
Win 15 points!
Okay!
banana
Go to last place!
Oops!
15
One common way to tie a clove hitch is to use two _____. a. slip knots b. half hitches c. square knots d. bowlines
half hitches
Oops!
Check
Okay!
Check
15
How is the fall zone for a forklift operation best defined? a. A minimum of a 30-foot diameter circle around the forklift. b. Twice the length of the base of the forklift. c. Any area into which the lifted materials could potentially fall.
Any area into which the lifted materials could potentially fall.
Oops!
Check
Okay!
Check
15
To transport a bottle of compressed gas, use a _____. a. hand truck b. cylinder cart c. wheelbarrow d. tunnel buggy
cylinder cart
Oops!
Check
Okay!
Check
15
Never stack or store materials _____. a. in cabinets b. on scaffolds c. outdoors d. on pallets
on scaffolds
Oops!
Check
Okay!
Check
15
When stacking bags of material that are the same width, step back and cross key the bags _____. a. in each tier above seven feet b. until the stack reaches four feet c. every 10 bags high d. all the way to the top of the pile
every 10 bags high
Oops!
Check
Okay!
Check
15
Before attempting to lift any material, _____. a. look for any protruding nails, wires, or sharp edges b. use a safety harness c. ask your supervisor for help d. ensure the stacking ratio is no greater than 3:1
look for any protruding nails, wires, or sharp edges
Oops!
Check
Okay!
Check
thief
Give points!
5
10
15
20
25
seesaw
Swap points!
Okay!
fairy
Take points!
5
10
15
20
25
lifesaver
Give 10 points!
Oops!
15
Before attempting to lower an overhead load, _____. a. put on a back support belt b. shrink wrap the load c. set up a fall zone d. size up the load
size up the load
Oops!
Check
Okay!
Check
monster
Reset all scores!
Oops!
seesaw
Swap points!
Okay!
fairy
Take points!
5
10
15
20
25
banana
Go to last place!
Oops!
15
What is the proper procedure to lift objects? a. Bend over with your knees straight, feet together, and then lift. b. Lift with your back, keep your legs straight, and keep your arms up. c. Lift with your legs, keep your back straight, and
Lift with your legs, keep your back straight, and keep your head up.
Oops!
Check
Okay!
Check
15
The knot shown in the figure above is a _____. a. square knot b. clove hitch c. half hitch d. bowline
clove hitch
Oops!
Check
Okay!
Check
15
To work with motorized material-handling equipment, a worker must be _____. a. trained, certified, and authorized b. experienced and knowledgeable c. a job foreman or supervisor d. licensed to drive
trained, certified, and authorized
Oops!
Check
Okay!
Check
monster
Reset all scores!
Oops!
gift
Win 20 points!
Okay!
gift
Win 20 points!
Okay!
lifesaver
Give 25 points!
Oops!
15
When using hand signals, always _____. a. stand on something at least two feet in height b. wear reflective gloves c. maintain eye contact with the operator d. make sure you can hear the backup alarm